Publications

    Print This Page

    Published/Edited BooksJournal PublicationsChapters Contributed Conference Proceedings

    Published/Edited Books

    Thermes 2007: Thermal Challenges in Next Generation Systems, Garimella, S.V. and Fleischer, A.S., eds. , Millpress, Rotterdam, the Netherlands, 2007.

    Refereed Journal Publications

    In review:

    O’connor, William, Warzoha, R., Weigand, R., Fleischer, A.S., Wemhoff, A.P., “Thermal Property Prediction and Measurement of Organic Phase Change Materials in the Liquid Phase near the Melting Point,” submitted to Applied Energy, Feb. 2014.

    Warzoha, R. and Fleischer, A.S., “Temperature-dependent Thermal Properties of a Paraffin Phase Change Material Embedded with Herringbone Style Graphite Nanofibers,” submitted to Applied Energy, Jan. 2014.

    In press:

    Warzoha, R. and Fleischer, A.S., “Heat Flow at Nanoparticle Interfaces,” accepted, Nano Energy, Jan. 2014.

     

    Published:

    Ebrahimi, K., Jones G.F., Fleischer, A.S.,  “A Review of Data Center Cooling Technology, Operating Conditions and the Corresponding Low-Grade Waste Heat Recovery Opportunities ,” Renewable and Sustainable Energy Reviews, 31, 622-638, 2014.

     

    Warzoha, R., Fleischer, A.S., “Determining the Thermal Conductivity of Liquids Using the Transient Hot Disk Method. Part I: Establishing Transient Thermal-fluid Constraints,” International Journal of Heat and Mass Transfer, 71, 779-789, 2014.

     

    Warzoha, R., Fleischer, A.S., “Determining the Thermal Conductivity of Liquids Using the Transient Hot Disk Method. Part II: Establishing an Accurate and Repeatable Solution Method,” International Journal of Heat and Mass Transfer, 71, 790-807, 2014.

     

    Warzoha, R., Sanusi, O., McManus, B., Fleischer, A.S., “Development of Methods to Fully Saturate Carbon Foam with Paraffin Wax Phase Change Material for Energy Storage,” Journal of Solar Energy Engineering, 135(2), 021007 (8), 2013.

    Warzoha, R., Zhang, D., Feng, G., Fleischer, A.S., “Engineering Interfaces in Carbon   Nanostructured Mats for the Creation of Energy Efficient Thermal Interface Materials,” Carbon, 61, 441-457. 2013.

    Warzoha, R., Sanusi, O., McManus, B., Fleischer, A.S., “Development of Methods to Fully Saturate Carbon Foam with Paraffin Wax Phase Change Material for Energy Storage,” Journal of Solar Energy Engineering, Volume 135, Issue 2, 021007 (8), 2013.

    S. Miller, B. Dunlap, A. Fleischer, “Cation Coordination and Interstitial Oxygen Occupancy in Co-Doped Zirconia from First Principles,” Solid State Ionics, Vol. 227, pp. 66-72, 2012.

    Chintakrinda, K, Warzoha, R., Weinstein, R.D., Fleischer, A.S., “Quantification of the Impact of Embedded Graphite Nanofibers on the Transient Thermal Response of Paraffin Phase Change Material Exposed to High Heat Fluxes,” J. Heat Transfer, Volume 134,  Issue 7, 071901 (10), 2012.

    Ehid, R., Fleischer, A.S., 2012, “Development and Characterization of Paraffin-based Shape Stabilized Energy Storage Materials," Energy Conversion and Management, Vol. 53, pp. 84-91.

    Ehid, R., Weinstein, R.D., Fleischer, A.S., 2012, “The shape stabilization of paraffin phase change material to reduce graphite nanofibers settling during the phase change process,” Energy Conversion and Management. Vol. 57, pp. 60-67.

    Ehid, R., Fleischer, A.S., 2012, “Development and Characterization of Paraffin-based Shape Stabilized Energy Storage Materials," Energy Conversion and Management, Vol. 53, pp. 84-91.

    Warzoha, R., Fleischer, A.S., 2011, “Thermal Management of High Density Power Electronics Modules Using Dielectric Mineral Oil with Applications in the Electric Utility Field for Smart Grid Protection,”, Journal of Thermal Science and Engineering Applications.  Volume 3,  Issue 4, 041005.

    Sanusi, O., Warzoha, R., Fleischer, A.S., 2011, “Energy Storage and Solidification Enhancements of Phase Change Materials embedded with Nanofibers,” International Journal of Heat and Mass Transfer, Vol. 54, No. 19/20, pp. 442-4436. 

    Chintakrinda, K., Weinstein, R., Fleischer, A.S., 2011, “A Direct Comparison of Three Different Material Enhancement Methods on the Transient Thermal Response of Paraffin Phase Change Material Exposed to High Heat Fluxes," International Journal of Thermal Sciences, Vol. 50, No. 9, pp. 1639-1647

    Warzoha, R., Fleischer, A.S., 2011, “Thermal Management of a 15kV/100kVA Intelligent Universal Transformer,” Journal of Thermal Science and Engineering Applications, Vol. 3, paper 011002.  

    Yakkatelli, R., Wu, Q., Fleischer, A.S., 2010, “A Visualization Study of the Flow Dynamics of a Single Round Jet Impinging on Porous Media,” Experimental Thermal and Fluid Science 34  pp. 1008-1015.

    Gandikota, V., Jones, G.F., Fleischer, A.S., 2010, “ Thermal Performance Of a Carbon Fiber Composite Material Heat Sink in an FC-72 Thermosyphon,”  Experimental Thermal and Fluid Science, 34, pp. 554-561.

    Gandikota, V., and Fleischer, A.S., “Experimental Investigation of the Thermal Performance of Graphite Foam for Evaporator Enhancement in both Pool Boiling and an FC-72 Thermosyphon,” Heat Transfer Engineering, Vol. 30, No. 8, 2009, pp.643-648.

    Garimella, S.V., Fleischer, A.S, Murthy, J.Y., Keshavarzi, A., Prasher, R., Patel, C., Bhavnani, S., Venkatasubramanian, R., Mahajan, R., Joshi, Y., Sammakia, B., Myers, B.A., Chorosinski, L., Baelmans, M., Sathyamurthy, P., Raad, P., “Thermal Challenges in Next Generation Systems,” IEEE Transactions on Components and Packaging Technology, Vol. 31, No. 4, 2008, pp. 801-815.

    Duda, J.C., Lagor, F.D., Fleischer, A.S., “A Flow Visualization Study of the Development of Vortex Structures in a Round Jet Impinging on a Flat Plate and a Cylindrical Pedestal,” Experimental Thermal and Fluid Science, Vol. 32, pp.1754-1758, 2008..

    Garimella, S.V. and Fleischer, A.S., “Foreword – Special Issue on Thermal Challenges in Next Generation Electronic Systems II,” Microelectronics Journal, Vol. 39, No. 7, July, 2008.

    Kopec, T.C., Weinstein, R.D., Fleischer, A.S., D’Addio, E. and Bessel, C.A., “The Effects of Embedding Phase Change Materials with Graphite Nanofibers for the Thermal Management of Electronics,” Journal of Heat Transfer, Vol. 130, No. 4, pp. 042405-1 – 042405-8, 2008.

    Harvest, J., Fleischer, A.S., Weinstein, R.D., “Modeling of the Thermal Effects Of Heat Generating Devices In Close Proximity On Vertically Oriented Printed Circuit Boards For Thermal Management Applications,” International Journal of Thermal Sciences, Vol. 46, No. 3, pp. 253-261, 2007.

    Fleischer, A.S., Johnson, B., Chang, L., “The Effect of Die Attach Voiding on the Thermal Resistance of Chip Level Packages” Microelectronics Reliability, Vol. 46, pp. 794-804, 2006.

    Fleischer, A.S., Troppenz, U., Hamacher, M., John. W., “Thermal Analysis of Bond Layer Influence on Performance of an All-Active Vertically-Coupled, Microring Resonating Laser” Microelectronics Reliability, Vol. 46, pp 421-431, 2006.

    Goldstein, R.J., Chiang, H.-D., Srinivasan, V., Fleischer, A.S., "Local Mass Transfer Measurements in an Inclined Enclosure at High Rayleigh Number", Heat and Mass Transfer, vol. 41, pp. 991-998, 2005.

    Fleischer, A.S., Nejad, S.R., “Jet Impingement Cooling of a Discretely Heated Portion of a Protruding Pedestal with a Single Round Air Jet,” Experimental Thermal and Fluid Science, Vol. 28, No. 8 pp. 893-901, 2004.

    Fleischer, A.S., Weinstein, R.D., and Khobragade, S.A., “Forced Convective Cooling of Electro-Optical Components Maintained at Different Temperatures on a Vertically Oriented Printed Circuit Board,” IEEE Transactions on Components and Packaging Technologies, Vol. 27, No. 2, pp. 296-304, 2004.

    Weinstein, R.D., Fleischer, A.S. and Krug, K., “Natural Convection and Passive Heat Rejection from Two Heat Sources Maintained at Different Temperatures on a Printed Circuit Board,” Journal of Electronics Packaging, Vol. 126, pp. 14-21, 2004.

    Fleischer, A.S., Goldstein, R.J., “High Rayleigh Number Convection of Pressurized Gases in a Horizontal Enclosure,” Journal of Fluid Mechanics, Vol. 469, pp. 1-12, 2002.

    Fleischer, A.S., Kramer, K., Goldstein, R.J., “Dynamics of the Vortex Structure of a Jet Impinging on a Convex Surface,” Experimental Thermal and Fluid Sciences, Vol. 24, pp. 169-175, 2001.

    Goldstein, R.J., Fleischer, A.S., Hogerton, P.B., “Electrochemical Mass Transfer at Moderate Rayleigh Numbers,” Journal of Heat Transfer, Vol. 123, pp. 1015-1017, 2001.

    Cornaro, C., Fleischer, A.S., Rounds, M., Goldstein, R.J., “Jet Impingement Cooling of a Convex Semi-Cylindrical Surface,” International Journal of Thermal Sciences, Vol. 40, pp. 890-898, 2001.

    Cornaro, C., Fleischer, A.S., Goldstein, R.J., “Flow Visualization of a Round Jet Impinging on Cylindrical Surfaces,” Experimental Thermal and Fluid Science, Vol. 20, pp. 66-78, 1999.

    Fleischer, A.S., McAssey, E.V., Jones, G.F., “Prediction of Pressure Drop in a Boiling Channel,” Journal of Heat Transfer, Vol. 121, pp.210-213, 1999.

          Chapters Contributed To Books

    Kopec, T., Fleischer, A.S., Weinstein, R.D., Bessel, C.A., 2007, "Transient thermal performance of phase change materials with embedded graphite nanofibers," in Thermes 2007: Thermal Challenges in Next Generation Systems, Garimella, S.V. and Fleischer, A.S., eds. , Millpress, Rotterdam, the Netherlands.

    Goldstein, R.J., Fleischer, A.S. and Cornaro, C., “A Visualization Study of Jet Impingement on Cylindrical Surfaces,” in Applied Optical Measurements, Eds.: M.Lehner, D.Mewes, U.Dinglreiter, R.Tauscher, Springer Verlag, pp. 307-318, 1999.

          Refereed Conference Proceedings

          Warzoha, R, Fleischer, A.S., “Thermal Property Prediction and Measurement of Organic Phase Change Materials in the Liquid Phase near the Melting Point,” Proceedings of the 2014 International Mechanical Engineering Congress and Exposition, Paper IMECE2014-36074,Montreal, Nov. 14-20, 2014.

    Ebrahimi, K., Jones, G.F., and Fleischer, A.S., “A Review of Challenging Issues in the Integration of Absorption Refrigeration and Organic Rankine Cycle into a Data Center Cooling System,” Proceedings of the 2014 Institute of Electrical and Electronics Engineers conference on thermal management, mechanical, thermomechanical and materials aspects associated with electronic and photonic components (ITherm), Paper 165, Orlando, FL, May 27-30, 2014.

     Weigand, Rebecca and Fleischer, A.S., “The influence of nanoparticle loading and surfactant on the viscosity of nanoenhanced energy storage materials,” Proceedings of the 2014 Institute of Electrical and Electronics Engineers conference on thermal management, mechanical, thermomechanical and materials aspects associated with electronic and photonic components (ITherm), Paper 11, Orlando, FL, May 27-30, 2014.

    Dalton, E. , Fleischer, A., Collins, M.N., Tao, J., Razeeb, K. ,  Punch, J. “Graphite nanofiber composite thermal interface material,” Proceedings of the International Conference on Soldering & Reliability (ICSR), Toronto, Ontario, Canada, May 2012.

    Miller, S., Fleischer, A.S., “Conductivity Measurement of Genetically Annealed Zirconia from Molecular Dynamics Simulations,” Proceedings of the 2012 International Mechanical Engineering Congress and Exposition, PaperIMECE2012-87962, Houston, Nov. 9-15, 2012.

          Warzoha, R. and Fleischer, A.S., “Development and testing of Subambient melt temperature nano-enhanced Phase change materials” 2012 Institute of Electrical and Electronics Engineers conference on thermal management, mechanical, thermomechanical and materials aspects associated with electronic and photonic components (ITherm), Paper 2875, San Diego, CA, May 30-June 1, 2012.

          Warzoha, R., McManus,B., Fleischer, A.S., “Evaluation of Methods to Fully Saturate Carbon Foam with Paraffin Wax Phase Change Material for Energy Storage,” 2012 Institute of Electrical and Electronics Engineers conference on thermal management, mechanical, thermomechanical and materials aspects associated with electronic and photonic components (ITherm), Paper 2874, San Diego, CA, May 30-June 1, 2012.

          Warzoha, R., Weinstein, R.D, and Fleischer, A.S “Thermophysical Properties of Nanoenhanced Phase Change Materials,” 2012 ASME Summer Heat Transfer Conference, Paper HT2012_58043, Puerto Rico, July 8-12, 2012.

          Fleischer, A.S., Wemhoff, A., Ural, A., O’Brien, J., Alaways, L., “Development and Execution of a Successful Mechanical Engineering Outreach Program for Middle School Girls Proceedings of the 2010 American Society of Engineering Education Regional Conference, Oct. 16-17, Villanova University, 2010.

          Clayton, G., O’Brien, J., Kroos, K., Fleischer, A.S., “Introduction to Mechanical Engineering  – A Hands on Approach,” Proceedings of the 2010 American Society of Engineering Education Annual Conference and Exposition, June 20-23, Louisville, KY, 2010.

          Sanusi, O., Fleischer, A.S., Weinstein, R.D. “An Investigation Into The Solidification Of Nano-Enhanced Phase Change Material For Transient Thermal Management Of Electronics,” Proceedings of the 2010 The Institute of Electrical and Electronics Engineers conference on thermal management, mechanical, thermomechanical and materials aspects associated with electronic and photonic components (ITherm), Las Vegas, NV, June 2-5, 2010, paper 2735.

          DiBella, E., Azeredo, I., Yakkatelli, R. and Fleischer, A.S. “A Flow Visualization Study of the Jet Dynamics in a Round Jet Impinging on a Foamed Aluminum Porous Media,” Proceedings of 2009 ASME International Mechanical Engineering Congress and Exposition, Paper 12193, Nov. 13-19, 2009.

          McCloskey, J, Fleischer, A.S., Patel, S., Ng, R., “The Determination of Thermal Properties of Paraffin-Based Phase Change Material [PCM] Within A Daylighting Panel,” Proceedings of 2009 ASME International Mechanical Engineering Congress and Exposition, Paper 12192, Nov. 13-19, 2009.

          Sanusi, O., Fleischer, A.S., “An Investigation into the Penetration of Phase Change Material in Carbon Foam for Transient Thermal Management ,” Proceedings of InterPACK 2009, Paper 89070, July 19-23, 2009, San Francisco, CA.

          Warzoha, R., Bird. S., Gandhi, M., Sundaram, A., Fleischer, A.S., “A Computational Study of the Thermal Performance of a 69kV/3000A Solid State Current Limiter under Transient Fault Current Loading,” Proceedings of InterPACK 2009, Paper 89071, July 19-23, 2009, San Francisco, CA.

          Warzoha, R., Bird. S., Gandhi, M., Sundaram, A., Fleischer, A.S., “ADesign of a Passive Cooling System for a Solid-State 15kV / 100kVA Intelligent Universal Transformer,” Proceedings of InterPACK 2009, Paper 89294, July 19-23, 2009, San Francisco, CA.

          Yakkatelli, R., Wu, Q., Fleischer, A.S., “A Flow Visualization Study of the Jet Dynamics in a Round Jet Impinging on a Foamed Aluminum Porous Media,” Proceedings of IMECE2008, Paper Number IMECE2008-66134, 2008 ASME International Mechanical Engineering Congress and Exposition, Oct. 31-Nov. 6, 2008, Boston, MA, USA.

          Kirby, P., Warzoha, R., Fleischer, A.S., “ A Computational Study of the Thermal Performance of a 69 kV Solid State Current Limiter Submerged in FR3 Dielectric Coolant,” Proceedings of IMECE2008, Paper Number IMECE2008-66135, 2008 ASME International Mechanical Engineering Congress and Exposition, Oct. 31-Nov. 6, 2008, Boston, MA, USA.

          Warzoha, R., Fleischer, A.S., “ A Computational Study of the Thermal Performance of a 15 kV Solid State Current Limiter Submerged in FR3 Dielectric Coolant,” Proceedings of IMECE2008, Paper Number IMECE2008-66483, 2008 ASME International Mechanical Engineering Congress and Exposition, Oct. 31-Nov. 6, 2008, Boston, MA, USA.

          Fleischer, A.S., Chintakrinda, K., Weinstein, R.D., Bessel, C.A., “Transient Thermal Management Using Phase Change Materials With Embedded Graphite Nanofibers For Systems With High Power Requirements,” Proceedings of the 2008 ITherm Conference, Orlando, FL, May 28-31, 2008.

          Comber, B., Fleischer, A.S., “Thermal Proximity Effects of Packaged RF High Power Amplifier Discretes,” Proceedings of IMECE2007, Paper Number IMECE2007-41221, 2007 ASME International Mechanical Engineering Congress and Exposition, November 11-15, 2007, Seattle, WA, USA.

          Kirby, P., Fleischer, A.S., “Thermal Interaction in Free Convection from Two Unequally Powered Discrete Heat Sources with Various Orientations and Separation Distances on a Vertical Plate,” Proceedings of IMECE2007, Paper Number IMECE2007- 44053, 2007 ASME International Mechanical Engineering Congress and Exposition, November 11-15, 2007, Seattle, WA, USA.

          Gandikota, V., Chengalvala, H., Fleischer, A.S., Jones, G.F., “Experimental Characterization of a Carbon Fiber Heat Sink in Boiling Heat Transfer Using FC-72,” Proceedings of IMECE2006, Paper Number IMECE2006-13356, 2006 ASME International Mechanical Engineering Congress and Exposition, November 5-10, 2006, Chicago, Illinois, USA.

          Weinstein, R.D., Kopec,T.C., D’Addio, E., Fleischer, A.S., Bessel, C.A., “Thermal Analysis Of Phase Change Materials With Embedded Carbon Nanofibers For Transient Thermal Management,” Proceedings of IMECE2006, Paper Number IMECE2006-13685, 2006 ASME International Mechanical Engineering Congress and Exposition, November 5-10, 2006, Chicago, Illinois, USA.

          Fleischer, A.S., Weinstein, R.D., Kopec, T., “Enhancement of Phase Change Materials Using an Embedded Carbon Fiber Heat Sink for Transient Thermal Abatement,” 2006 ITherm Conference, San Diego, CA, May 30 – June 2, 2006.

          Chengalvala, H., Fleischer, A.S., Jones, G.F., “Experimental Characterization of A Unique Carbon Fiber Brush Heat Sink In Two-Phase Heat Transfer,” ASME IMECE 2005, Orlando, FL, Nov. 11-16, 2005, Paper # 79143.

          Fleischer, A.S., Johnson, B.C., Chang, L., “The Effect of Die Attach Voiding on the Thermal Resistance of Chip Level Packages,” Proceedings of IPACK2005, ASME InterPACK ’05, Paper # IPACK2005-73224, July 17-22, San Francisco, CA, 2005.

          Harvest, J., Fleischer, A.S., Weinstein, R.D., “Thermal Management Of Heat Generating Devices In Close Proximity On Printed Circuit Boards,” Proceedings of HT2005, 2005 ASME Summer Heat Transfer Conference, Paper #HT2005-72254, July 17-22, San Francisco, CA, 2005.

          Fleischer, A.S, Nejad, S.R., “Experimental Investigation of Heat Transfer from a Discretely Heated Protruding Pedestal to a Single Round Impinging Air Jet” Proceedings of IMECE2004, Paper # IMECE2004-59011, 2004 ASME International Mechanical Engineering Conference and Exposition, Anaheim, CA Nov. 13-19, 2004.

          Fleischer, A.S., Troppenz, U., Hamacher, M., John, W., “Thermal Characterization of an All-Active Microring Resonating Laser,” Proceedings of IMECE2004, Paper # IMECE2004-60399, 2004 ASME International Mechanical Engineering Conference and Exposition, Anaheim, CA Nov. 13-19, 2004.

          Fleischer, A.S., Weinstein, R.D., “An Experimental Investigation of the Thermal Interaction of Electro-Optical Components on a Printed Circuit Board in Natural and Forced Convection,” Proceedings of the 2003 ASME Summer Heat Transfer Conference, Paper # HT2003-47376, 2003 Summer Heat Transfer Conference, Las Vegas, NV, July 20-23, 2003.

          McAssey, E.V., Fleischer, A.S., “Engine Cooling System Stability,” Proceedings of the 2001 SAE 5th Conference on Vehicle Thermal Management Systems, Paper # 01VTMS-49, Nashville, TN, May, 2001.

          Cornaro, C., Fleischer, A.S., Goldstein, R.J., “Jet Impingement on Concave and Convex Surfaces,” Proceedings of the 8th International Symposium on Flow Visualization, pp. 236-1 – 236.12, Sorrento, Italy, Sept. 1-4, 1998.

          Fleischer, A.S., McAssey, E.V., Jones, G.F., “Influence of Bubble Formation on Pressure Drop in a Uniformly Heated Vertical Channel,” Proceedings of the 32nd National Heat Transfer Conference, Vol. 4, pp. 51-57, 1997 ASME National Heat Transfer Conference, Baltimore, MD, Aug. 10-12, 1997.

          Fleischer, A.S., Jones, G.F., McAssey, E.V., “Prediction of Pressure Drop in a Uniformly Heated Channel Under Boiling Conditions,” 5th International Conference on Nuclear Engineering Proceedings, ICONE 1997, ASME, New York, NY, pp.685, 1997.